Sky+ AV Amplifier Remote Codes

Programming Procedure by Direct Set

sky+remoteThis procedure is used to programme or re-program the Sky+ Remote Control Unit (RCU) to operate your AV Amplifier functions.
This procedure is used when the RCU is not operating some or all of the AV Amplifier functions. It is possible that either the installer may not have set the RCU to the correct code or the customer may have changed their AV Amplifier since the original installation took place. In such circumstances it will be necessary to re-programme the RCU to the correct model of AV Amplifier.

Before proceeding further place your Sky+ RCU on a flat surface such as the floor or a coffee table.

  1. Turn on the AV amplifier you wish to operate, press the TV button on the Sky+ RCU (Remote Control Unit).
  2. Press and hold down the Select then the 0 (zero) buttons on the Sky+ RCU until the LED (Light Emitting Diode) blinks twice.
  3. Input the 4 digit number from the Sky+ RCU direct set code list pages. The LED should flash twice to confirm that the code was entered successfully.
  4. Use the Left navigation button on the Sky+ RCU to try and switch the AV Amplifier into standby. If the standby button works then the other AV Amplifier functions should also work and the correct code has been selected.
    If all functions do not work correctly then repeat steps 1 – 3 and work through all the 4 digit numbers from the Sky+ RCU direct set code list pages until you find the code which supports all or as many of the AV Amplifier functions as possible.

 

Important

The most popular codes are sorted first within the Sky+ RCU direct set code list, therefore the codes should be attempted in sequence one after the other.
The remote control will operate all functions on the digibox (whilst in Sky mode) however it does not support the functions on their AV Amplifier at the current time. You must therefore keep your AV Amplifier RCU to hand to control the amplifier functions.
Sky remotes do not currently have any learning function.


 

AV Amp Volume/Mute Control Punch Through

If your Sky+ remote is fairly new or you have the Sky Navigator remote it may be possible to set the normal volume/mute controls to work your amp rather than the TV, without pressing the TV key.

Proceed as follows:

  1. Program the remote as detailed above to control your amp using the arrow keys in TV mode
  2. Press TV Key
  3. Hold down select and press 1 until the remote’s LED flashes twice (if it only flashes once or remains on steady, your remote does not support this feature)
  4. Press Sky key and enjoy

To reverse the process press select and 2 rather than 1.


 

Manufacturer
Codes
Aiwa
0149 or 0186 or 1433
Akai
0143 or 0468
Alba
0587
Amstrad
0830 or 0772
Arcam
0669 or 0297
Audiolab
0297 or 1217
Bat
0297
Bush
0297 or 0449 or 0875
Clatronic
0772
Denon
0032 or 0188
Elta
0772
Garrard
0468 or 0772
Genexxa
0468
Goldmund
0297
Goodmans
0468 or 0772 or 0449 or 1081
Grundig
0297 or 0875 or 1217 or 1117 or 0772
Harman/Kardon
0138
Harwood
0772
Inkel
0055 or 0530
Intersound
0772
JBL
0138
JVC
0102 or 0492
Kenwood
1055 or 1341 or 1597 or 0341 or 0342 or 0055
Koss
0772
Linn
0297
LXI
0772
Marantz
0297 or 1117 or 1217
Mark
0297
Matsui
0772
Mafui
0342
Meridian
0297
Micromega
0297 or 1217
Minton
1123
Mitsubishi
0468
Mx Onda
0772
Myryad
0297 or 1217
Naim
0297
Nikkei
0772
NTDE
0772
Okano
0468
Orient
Power 0772
Pace
0828
Panasonic
0336 or 1336 or 1337 or 1546
Philips
1117 or 1217 or 0669 or 0297
Phontrend
0530
Pioneer
0297 or 0317
Pye
0875
Quad
0297
RadioShack
0772
Revox
0297
Roadstar
0875
Sansui
1117
Sanyo
0772
Schneider
1081 or 0138 or 0772
Sherwood
0530
Sony
1086 or 1186 or 1286 or 1786
Taekwang
0468
Teac
0449
Technics
1336 or 1337 or 1546
Telefunken
0875
Thorens
0297 or 1217
Thorn
0772
Universum
0297 or 0772 or 0468
Victor
0102
Videologic
1123
Wharfedale
0468
Yamaha
0204 or 1304
Zenith
0772
 
Share Button